Delphi Suspension Stabilizer Bar Bushing Kit P/N:TD4534W
$41.99
(You save)
Keep your front stabilizer bar quietly controlling body roll with the Delphi Suspension Stabilizer Bar Bushing Kit (TD4534W). These bushings cushion the front sway bar where it mounts to the chassis, isolating vibration and letting the bar twist to limit body lean through corners. This kit is a direct-fit replacement for the 2015-2017 Audi Q3, 2015-2017 Audi Q3 Quattro, 2009-2017 Volkswagen CC, 2006-2010 Volkswagen Passat, 2009-2010 Volkswagen Passat CC, and 2009-2017 Volkswagen Tiguan — see the Buyer's Guide tab for engine-level details.
Designed to OE standards: Delphi applies its OE steering and suspension expertise to the aftermarket portfolio.
Built for consistent life: manufactured for repeatable, dependable performance.
Quieter operation: manufactured to reduce noise from the stabilizer bar mounting points.
Validated to extremes: tested below -40°C and above 120°C and exposed to 720 hours of salt spray, with dimensional and material analysis for OE-to-aftermarket compatibility.
Delphi bushings assist in restoring the smooth ride of the vehicle. Worn sway bar bushings can produce clunking or rattling over uneven surfaces and looser handling; if that is the cause, this kit replaces them.
Interchange: 3C0 411 303 AA · 3C0 411 303 T 3C0411303AA · 3C0411303T · BSK43019 · K200889 · JBU2111
This part cross-references / interchanges with the following part numbers:
It cushions the front stabilizer bar where it mounts to the chassis, isolating vibration and allowing the bar to twist so it can help control body roll during cornering.
Is this a front or rear kit?
This is a front stabilizer bar bushing kit, matching the front position on the listed applications.
Which vehicles does the Delphi TD4534W fit?
It fits the 2015-2017 Audi Q3 and Q3 Quattro, 2009-2017 Volkswagen CC, 2006-2010 Passat, 2009-2010 Passat CC, and 2009-2017 Tiguan. Check the Buyer's Guide tab for details.
What are signs these bushings may need replacing?
Clunking or rattling from the front over bumps, and looser or less responsive handling. If worn bushings are the cause, this kit replaces them; diagnose the source first.
How were these Delphi bushings tested?
They are tested below -40°C and over 120°C and exposed to 720 hours of salt spray, with dimensional and material analysis to ensure OE-to-aftermarket compatibility.
Write a Review
Delphi
Delphi Suspension Stabilizer Bar Bushing Kit P/N:TD4534W
Quiet a clunking, rattling front sway bar and help keep your Mercedes-Benz cornering flat with the Delphi Suspension Stabilizer Bar Bushing Kit TD5885W. This front-to-frame stabilizer bar bushing kit...
Quiet a clunking front sway bar and keep the stabilizer bar located where it belongs with the Delphi Suspension Stabilizer Bar Bushing Kit TD671W. These front stabilizer bar bushings cushion the bar...
Quiet a clunking front sway bar and keep the stabilizer bar properly located with the Delphi Suspension Stabilizer Bar Bushing Kit (TD994W). It drops in as a direct-fit replacement for the front...
Quiet a clunking rear sway bar and keep it precisely located with the Delphi Suspension Stabilizer Bar Bushing Kit (TD935W). This rear kit drops in for a wide range of BMW models, including the...
Quiet down clunks and steady the front sway bar with the Delphi Suspension Stabilizer Bar Bushing Kit TD5755W, a direct-fit replacement for the 2002-2006 Nissan Sentra. These front stabilizer bar...
WARNING:
These products can expose you to chemicals including lead and phthalates, which are known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to
www.P65Warnings.ca.gov.
