Monroe Shocks & Struts Suspension Strut and Coil Spring Assembly P/N:272314
$150.99
(You save)
Get a full corner of front suspension back in one bolt-in unit with the Monroe Quick-Strut Suspension Strut and Coil Spring Assembly 272314. This front-left assembly is a direct-fit replacement for the 2007-2013 BMW 328i and 335i, the 2008-2013 BMW 128i and 135i, the 2011-2013 BMW 335is, and the 2013 BMW 135is. Fit-checked and ride-tested, it's engineered to restore factory ride height and ride performance.
Complete Repair: preassembled strut, application-specific coil spring, and upper strut mount in a single unit — no spring compressor needed.
Restores Ride Height: the coil spring is calibrated to the OE design to help restore ride height and support the vehicle's weight.
Vehicle-Specific Design: application-specific spring, mount, and strut designs for ride and handling tuned to this vehicle profile.
Rust Resistance: a protective coating resists rust and corrosion, and the unit is salt-spray tested.
The premium upper strut mount is built for smooth, like-new steering precision while helping reduce noise, vibration, harshness, and memory steer, and the assembly helps reduce body sway and road harshness before it reaches the cabin. Backed by Monroe's Limited Lifetime Warranty and the exclusive Feel the Difference Guarantee.
This part cross-references / interchanges with the following part numbers:
LS3381111L, LS5391941L, 33BW1100, 92140252
Frequently Asked Questions
What is the Monroe Quick-Strut 272314?
It's a front-left complete strut and coil spring assembly that combines the strut, an application-specific coil spring, and the upper mount in one preassembled unit for the listed BMW models.
Which vehicles does this assembly fit?
The front-left position on the 2007-2013 BMW 328i and 335i, the 2008-2013 128i and 135i, the 2011-2013 335is, and the 2013 135is. See the Buyer's Guide tab to confirm your vehicle.
Do I need a spring compressor to install it?
No. The unit arrives fully assembled, so you can install it without compressing a coil spring, which makes the strut replacement quicker and easier.
Is this a front or rear part, and which side?
It is a front-left assembly. Order the matching part for the opposite corner if you need the right side.
Should I replace both sides at the same time?
Replacing struts as a pair on the same axle is recommended for balanced ride and handling. This listing covers one front-left assembly.
Write a Review
Monroe
Monroe Shocks & Struts Suspension Strut and Coil Spring Assembly P/N:272314
Restore factory ride height and control at the front of your truck with the Monroe Quick-Strut Suspension Strut and Coil Spring Assembly 271100. This fully assembled front unit drops in as a...
Ride tall and smooth again with the Monroe Quick-Strut 172621 Front Left Suspension Strut and Coil Spring Assembly, a fully preassembled, vehicle-specific unit that drops in as a direct-fit...
Smooth out a worn front corner with the Monroe Quick-Strut 271691L, a fully assembled front left Honda Accord strut assembly that ships as a complete strut and coil spring assembly. It's a direct-fit...
Bring back factory ride height and controlled handling with the Monroe Quick-Strut 171615 Front Suspension Strut and Coil Spring Assembly — a fully preassembled Ford Taurus strut assembly that...
Take the guesswork out of front strut service with the Monroe Quick-Strut 171348R Front Right Suspension Strut and Coil Spring Assembly, a fully assembled front-right unit that drops in as a...
WARNING:
These products can expose you to chemicals including lead and phthalates, which are known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to
www.P65Warnings.ca.gov.
