A1 CARDONE 19-B1583 rear left brake caliper for the 1991-1997 Honda Accord and other vehicles squeezes the pads against the rotor to slow the wheel. This remanufactured A1 CARDONE brake caliper is an unloaded floating design with one piston.
- Every unit is 100% pressure-tested
- Steel piston that resists cracking and pitting and handles heavy loads
- Rubber seals replaced with new high-temperature EPDM rubber
- Treated with a specially formulated rust inhibitor
- New bleeder screw for trouble-free bleeding and a positive seal
- Plastic cap plug on every brake port thread
Quick facts
- Part: A1 CARDONE 19-B1583 brake caliper
- Also called: disc brake caliper
- Fits: 1991-1997 Honda Accord and other vehicles
- Position: Rear left
- Material: Cast iron (casting), steel (piston)
- Condition: Remanufactured
A disc brake caliper that sticks or leaks can show up as the car pulling to one side under braking, uneven pad wear or fluid around the caliper. These signs alone do not prove the caliper is the problem, since a collapsed brake hose can cause them too.
Fits
It is a Honda Accord rear caliper for the 1991-1997 model years, and the vehicles it fits include the 1995-1998 Acura TL and the 1992-1994 Acura Vigor. Each side of the rear axle takes one caliper; this listing is the rear left, sold one per listing, and the rear right is a separate part normally done at the same time.
Specifications
Fit and size
- Position: Rear left
- Quantity per application: 1
- Caliper type: Floating
- Piston diameter: 38.09 mm (1.5 in), 1 piston
- Inlet port size: 10 mm (0.394 in), inverted flare, thread M10x1.0
- Mounting hole: 10 mm (0.394 in), thread M10x1.25
- Bleeder thread size: M10x1.25
Build and materials
- Condition: Remanufactured, unloaded
- Caliper material: Cast iron
- Piston material: Steel
- Finish: Oil emulsion
- Rust-resistant coating: Yes
- Country of origin: Mexico
In the box
One brake caliper, mounting bracket, hardware kit and instruction sheet. The hardware includes abutment clips, an anti-rattle spring, a bleeder screw and dust boots. Pads, mounting bolts and a bleeder screw cap are not included, so plan on new mounting bolts rather than reusing the old ones.
Installation notes
- An instruction sheet comes with the caliper for the steps.
- Programming is not required.
- Use the brake fluid the vehicle maker recommends, from a new sealed container.
Interchange: 43019SV5A00 · 43230SL5A01
Frequently Asked Questions
Is this the right 1991-1997 Honda Accord caliper?
Yes, the A1 CARDONE 19-B1583 rear left brake caliper fits the 1991-1997 Honda Accord. If your car is another model, look it up in the "Vehicles it fits" section on this page.
Is this the 1995-1998 Acura TL brake caliper?
Yes. It is the rear left caliper for the 1995-1998 Acura TL, sold one per listing.
What hardware comes with this unloaded rear left brake caliper?
A1 CARDONE 19-B1583 comes with its bracket and a hardware kit of abutment clips, an anti-rattle spring, a bleeder screw and dust boots. Pads and mounting bolts are not included.
Can I swap a phenolic piston caliper for this steel piston one?
No, swapping is not recommended. The original manufacturers specified steel or phenolic pistons for each vehicle's intended use, so follow the vehicle maker's recommendation. This caliper has a steel piston.
What grease goes on the mounting pins of this floating caliper?
A silicone grease is used on floating caliper mounting pins. That applies to the A1 CARDONE 19-B1583, which is a floating-type caliper.
