Bring firm, quiet braking back to your car's front-right corner with the Raybestos R-Line Remanufactured Semi-Loaded Disc Brake Caliper and Bracket Assembly (FRC10906). This floating caliper installs as a direct-fit replacement for the 1997-2003 Chevrolet Malibu, 2004-2005 Chevrolet Classic, 1999-2004 Oldsmobile Alero, 1997-1999 Oldsmobile Cutlass, and 1999-2005 Pontiac Grand Am (All engines).
Remanufactured from OE parts: castings, guide pins, and brackets are carefully inspected before being re-used, with materials matching OE specifications.
New sealing components: to promote leak-free operation, the seals, boots, bleeder screws, abutment hardware, banjo bolts, and O-rings are replaced with new materials.
EPDM70 rubber components: for heat resistance, performance, and durability; silicone boots are used on heavy-duty applications where applicable.
100% pressure tested to help ensure reliable braking performance.
Built as a floating aluminum-casting caliper with a 2.378 in (60.4 mm) piston and an M10x1 bleeder screw thread, it ships as a semi-loaded caliper and bracket assembly. Sold individually for the front-right position; for even, balanced braking it is best practice to service the matching side as a pair. Country of origin: Mexico.
Which vehicles and position does this caliper fit?
It is cataloged for the front-right position on the 1997-2003 Chevrolet Malibu, 2004-2005 Chevrolet Classic, 1999-2004 Oldsmobile Alero, 1997-1999 Oldsmobile Cutlass, and 1999-2005 Pontiac Grand Am (All engines).
Is FRC10906 new or remanufactured?
It is a Raybestos R-Line remanufactured semi-loaded caliper and bracket assembly. Castings, guide pins, and brackets are inspected and re-used, while the rubber and sealing parts are replaced with new materials.
What sealing parts are replaced during remanufacturing?
The seals, boots, bleeder screws, abutment hardware, banjo bolts, and O-rings are replaced with new materials to support leak-free operation, and each unit is 100% pressure tested.
Do I need to replace both calipers?
This listing is for one caliper sold individually for the front-right position. For even, balanced braking it is best practice to service the matching side at the same time as a pair.
What are the key specifications?
It is a floating caliper with an aluminum casting, a 2.378 in (60.4 mm) piston, and an M10x1 bleeder screw thread, supplied as a semi-loaded caliper and bracket assembly.
Bring firm, consistent braking back to your van with the Raybestos R-Line Remanufactured Semi-Loaded Disc Brake Caliper and Bracket Assembly (MPN FRC11579). The caliper houses the piston that presses...
Clamp the pads against the rotor and keep the rear right corner stopping smoothly with the Raybestos R-Line Remanufactured Semi-Loaded Disc Brake Caliper and Bracket Assembly, MPN FRC11580. It's a...
Replace a worn or leaking front-left brake caliper with the Raybestos R-Line Remanufactured Semi-Loaded Disc Brake Caliper and Bracket Assembly (MPN FRC11953). This front-left unit installs as a...
Clamp the front-left brake pads to the rotor with the Raybestos R-Line Remanufactured Semi-Loaded Disc Brake Caliper and Bracket Assembly (FRC11586). This floating, cast-iron caliper installs as a...
WARNING:
These products can expose you to chemicals including lead and phthalates, which are known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to
www.P65Warnings.ca.gov.
