Delphi Suspension Control Arm and Ball Joint Assembly P/N:TC1385
$116.99
(You save)
Tighten up steering response and restore secure front suspension geometry with the Delphi control arm and ball joint assembly, MPN TC1385. This is a front left lower unit that locates the wheel and provides the lower pivot point through its integrated ball joint. It's a direct-fit replacement for a long list of Mercedes-Benz applications, including the 2007-2011 CLS550, 2007-2011 CLS63 AMG, 2003-2009 E320, 2006-2009 E350, 2003-2006 E500, 2003-2006 SL500, 2003-2008 SL55 AMG and 2004-2010 SL600 — see the Buyer's Guide tab for the full list of covered years, makes and models.
OE-validated durability: tested below -40°C and above 120°C and exposed to 720 hours of salt spray, with dimensional and material analysis for close OE-to-aftermarket compatibility.
100% inspected: every control arm undergoes crack detection and ultrasonic flaw detection so materials match OE specifications.
Precision ball studs: studs machined to micron tolerances for durable, smooth joint operation.
Robot-welded, corrosion-protected: robot welding for consistent quality, with anti-corrosion protection applied for corrosion prevention and enhanced appearance.
Signs the original may need replacing include clunking on acceleration, deceleration or over uneven pavement, loose or wandering steering, and uneven tire wear. If a worn control arm or ball joint is the cause, this assembly replaces it.
Frequently Asked Questions
What is the Delphi TC1385 control arm with ball joint?
It's a front left lower suspension control arm with an integrated ball joint that locates the wheel and provides the lower pivot point, combining the arm and joint in one bolt-in unit.
Which vehicles does the TC1385 fit?
It fits many Mercedes-Benz models, including the 2007-2011 CLS550, 2003-2009 E320, 2006-2009 E350, 2003-2008 SL55 AMG and 2004-2010 SL600. Check the Buyer's Guide tab for the complete list.
What position is this control arm?
It is the front left lower control arm. Verify it matches the corner you're servicing on your vehicle before ordering.
How is this Delphi control arm tested for durability?
Delphi tests below -40°C and over 120°C, exposes each part to 720 hours of salt spray, and runs 100% crack and ultrasonic flaw detection so materials match OE specifications.
What are common signs this control arm or ball joint needs replacing?
Watch for clunking on acceleration, deceleration or over bumps, loose or wandering steering, and uneven tire wear. Have the cause diagnosed, since these signs can have other sources.
Write a Review
Delphi
Delphi Suspension Control Arm and Ball Joint Assembly P/N:TC1385
Restore precise wheel location and smooth, controlled steering with the Delphi control arm and ball joint assembly (TC1346), a direct-fit replacement for the rear left upper rearward position on the...
Restore steering precision and confident wheel control with the Delphi control arm and ball joint assembly (P/N: TC5901), a direct-fit replacement for the front left upper position on the 2003-2004...
Steer with confidence and keep your front suspension tight with the Delphi control arm and ball joint assembly (P/N: TC6247). This is the front left upper unit, dropping in as a direct-fit...
Keep your steering precise and your ride stable with the Delphi control arm and ball joint assembly (P/N: TC1393), a direct-fit replacement for the front right lower rearward position on the...
Tighten up your Audi's front end and quiet a worn joint with the Delphi control arm and ball joint assembly (TC2455) — a Delphi control arm that installs as a front right lower rearward, direct-fit...
WARNING:
These products can expose you to chemicals including lead and phthalates, which are known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to
www.P65Warnings.ca.gov.
