Delphi HP10277 fuel pump hanger for the 1992-1996 Ford F-150 6-cylinder 4.9L, V8 5.0L or 5.8L and other vehicles mounts in the fuel tank and carries the float arm used for the gas gauge reading.
- Designed for operation under extreme temperatures and quick engine starts
- Metal tubes routed so they never touch the tank, which removes noise and vibration while the vehicle runs
- Empty float height and float retention set for a correct gas gauge reading
- Lower amperage draw puts less load on the vehicle's electrical system
- Validated and tested before sale
Quick facts
- Part: Delphi HP10277 fuel pump hanger
- Also called: fuel pump hanger assembly
- Fits: the 1992-1996 Ford F-150 6-cylinder 4.9L, V8 5.0L or 5.8L and other vehicles
- Condition: New
A gas gauge that reads wrong, hard starting or noise from the tank can mean the hanger is worn. These signs alone do not prove it, since a clogged fuel filter is another common source of hard starting. If the fuel pump hanger assembly is the cause, this one replaces it. A shop can test the fuel system.
Fits
The 1992-1996 Ford F-150 6-cylinder 4.9L, V8 5.0L or 5.8L, the 1992-1996 Ford F-250 6-cylinder 4.9L, V8 5.0L, 5.8L or 7.5L and the 1992-1996 Ford F-350 6-cylinder 4.9L plus the 1992-1997 F-350 V8 5.8L or 7.5L take this hanger, and so do other vehicles. The fitment calls for one hanger per truck.
Specifications
- Quantity per vehicle: 1
- Condition: New
- Float arm: included
In the box
One fuel pump hanger with float arm, jumper harness, lock ring, retainers, seal, splices and an instruction sheet.
Installation notes
- Check and clean the fuel tank before installing the hanger.
- An instruction sheet comes with the part for the steps.
Interchange: 953-3004 · F6TZ 9A407-BA · F6TZ 9A407-BB · PFB-2
4011015 · 4017205 · E2059MN · DHP10277 · 67000 · P74107 · P77254S · P77398H · P77399H · RE0022P · SP154 · SP2006H · SP2010H · USEP12302M
This part cross-references / interchanges with the following part numbers:
4011015, 4017205, E2059MN, DHP10277, 67000, P74107, P77254S, P77398H, P77399H, 953-3004, RE0022P, F6TZ 9A407-BA, F6TZ 9A407-BB, PFB-2, SP154, SP2006H, SP2010H, USEP12302M
Frequently Asked Questions
Is the Delphi HP10277 hanger right for a 1992-1996 Ford F-150 6-cylinder 4.9L, V8 5.0L or 5.8L?
Yes. Delphi HP10277 fits the 1992-1996 Ford F-150 with the 6-cylinder 4.9L, V8 5.0L or 5.8L. For another truck, look up your own vehicle in the "Vehicles it fits" section.
Does the HP10277 hanger come with a lock ring and seal?
Yes. Delphi HP10277 comes with the float arm, jumper harness, lock ring, retainers, seal, splices and an instruction sheet.
How is the float arm on this Delphi hanger set up for the gas gauge?
The empty float height and float retention are set for a correct gas gauge reading, and the float arm comes with the hanger.
Do the metal tubes on this fuel pump hanger touch the tank?
No. The metal tubes are routed so they do not contact the tank at any point, which removes noise and vibration while the vehicle runs.
Should the tank be cleaned before installing the Delphi HP10277 hanger?
Yes. Check and clean the fuel tank before the hanger goes in. An instruction sheet comes with the part for the steps.
