Delphi Suspension Control Arm and Ball Joint Assembly P/N:TC1755
$79.99
(You save)
Sharpen steering response and quiet worn-suspension clunks with the Delphi Suspension Control Arm and Ball Joint Assembly (TC1755) — a front left upper Ford Fusion control arm built to Delphi's OE engineering standards. This control arm and ball joint assembly is a direct-fit replacement for the 2006-2012 Ford Fusion, 2007-2012 Lincoln MKZ, 2006 Lincoln Zephyr, 2003-2013 Mazda 6, and 2006-2011 Mercury Milan; see the Buyer's Guide tab for engine-level fitment.
Delphi applies its OE steering expertise to the aftermarket, and this Delphi control arm is validated hard:
OE-level durability testing: withstands temperatures below -40°C and over 120°C and is exposed to 720 hours of salt spray, with extensive dimensional and material analysis for OE-to-aftermarket compatibility.
100% inspection: crack detection and ultrasonic flaw detection so materials match OE specifications.
Precision joint: ball studs machined to micron tolerances for smooth joint operation and durability.
Built to last: robot welding for consistent quality, plus anti-corrosion protection on each part for corrosion prevention and enhanced appearance.
The control arm locates the wheel and the integrated ball joint allows suspension and steering movement. If a worn arm or ball joint is the cause of clunking, wandering steering, or uneven tire wear, replacing this front left upper unit addresses it.
Frequently Asked Questions
What vehicles does the Delphi TC1755 control arm fit?
It is a direct-fit replacement for the 2006-2012 Ford Fusion, 2007-2012 Lincoln MKZ, 2006 Lincoln Zephyr, 2003-2013 Mazda 6, and 2006-2011 Mercury Milan. See the Buyer's Guide tab for full engine-level fitment.
Where is this control arm and ball joint assembly located?
This unit is cataloged for the front left (driver-side) upper position. Confirm it matches the corner you are servicing before ordering.
Does the Mazda 6 control arm include the ball joint?
Yes. TC1755 is an assembly with the ball joint integrated into the arm, so you replace both together rather than pressing in a separate joint.
What are signs this control arm may need replacing?
Clunking over the road, wandering or loose steering, and uneven tire wear can indicate a worn arm or ball joint. Diagnose the cause first, since these symptoms can have other sources.
How is Ford Fusion control arm replacement cost affected by this part?
This listing covers the TC1755 assembly itself; total replacement cost also depends on labor, an alignment, and whether other corners need service. It is sold individually for the front left upper position.
Write a Review
Delphi
Delphi Suspension Control Arm and Ball Joint Assembly P/N:TC1755
Shopping for a Honda Civic control arm? The Delphi Suspension Control Arm and Ball Joint Assembly (TC1075) is a front right upper unit that installs as a direct-fit replacement on the 1996-2000 Honda...
Keep your front suspension located and tracking properly with the Delphi Suspension Control Arm and Ball Joint Assembly TC1043 — a Honda Accord control arm built with Delphi's OE steering expertise...
Steer straight and keep your front suspension tight with the Delphi Suspension Control Arm and Ball Joint Assembly, TC3751 — a direct-fit Honda Civic control arm that drops into the front left lower...
Sharpen loose, wandering steering with the Delphi Suspension Control Arm and Ball Joint Assembly TC5364 — a 350Z lower control arm that installs in the front right lower rearward position on the...
Delphi control arm engineering comes to your BMW's rear suspension with the Delphi Suspension Control Arm and Ball Joint Assembly (TC2954). It installs as a direct-fit replacement for the rear left...
WARNING:
These products can expose you to chemicals including lead and phthalates, which are known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to
www.P65Warnings.ca.gov.
