Monroe Shocks & Struts Suspension Shock Absorber and Coil Spring Assembly P/N:58653
$180.99
(You save)
Handle the extra weight when you tow or haul with the Monroe Load Adjusting Rear Suspension Shock Absorber and Coil Spring Assembly 58653, a pre-assembled shock-and-spring unit sold as a Pack of 2. It's a direct-fit replacement for the 2009-2014 Ford F-150 (see the Buyer's Guide tab for engine-level fitment). Ideal for light trucks that occasionally carry or tow varying loads, each unit pairs a nitrogen gas-charged shock with a heavy-gauge, calibrated coil spring that adjusts to changing road and weight conditions for extra control when the job gets demanding.
Reduces sag under load: the heavy-gauge, calibrated coil spring helps reduce rear-end sag when loaded up to 1,200 lbs. (capacity limited by suspension, tires and transmission; see owner's manual).
Application-tuned valving: full-displaced valving is tuned for each application and adjusts to road extremes to help provide a consistent ride.
Friction-reducing build: OE all-weather fluid with special modifiers handles temperature extremes, and a PTFE-banded piston helps reduce friction against the pressure tube.
Durable rod & seal: a self-lubricating fluid seal retains gas while a heavy-duty nitrocarburized rod is built for long service life.
The nitrogen gas charge helps maintain tire-to-road contact by reducing aeration and shock fade.
Interchange: SC00032 · G64079 · 554373 · 252600
This part cross-references / interchanges with the following part numbers:
SC00032, G64079, 554373, 58653, 252600
Frequently Asked Questions
What vehicles does the Monroe 58653 fit?
It's a direct-fit rear assembly for the 2009-2014 Ford F-150. Check the Buyer's Guide tab to confirm the fit for your specific truck and engine.
How many units come in the box?
This listing is a Pack of 2, so you get a matched pair for the rear axle. Installing both sides together helps keep ride balance and even wear.
What makes these Load Adjusting shocks different?
They add a heavy-gauge, calibrated coil spring to the shock that adjusts to changing road and weight conditions, helping reduce rear sag when hauling or towing varying loads.
How much load can the coil spring support?
The calibrated coil spring helps reduce sag when loaded up to 1,200 lbs. Actual capacity is limited by your suspension, tires and transmission—see your owner's manual.
What are signs these assemblies may need replacing?
Excessive rear sag under load, a bouncy or unstable ride, bottoming out, uneven tire wear, or fluid leakage from the shock body can indicate worn units. Diagnose the cause before replacing.
Write a Review
Monroe Shocks & Struts
Monroe Shocks & Struts Suspension Shock Absorber and Coil Spring Assembly P/N:58653
Keep your loaded van riding level and controlled with the Monroe Load Adjusting Suspension Shock Absorber and Coil Spring Assembly 58605, a ready-to-install rear assembly sold as a pack of 2. It's a...
Level out sag and keep a loaded truck composed with the Monroe Load Adjusting Suspension Shock Absorber and Coil Spring Assembly 58630. This pre-assembled unit fits the rear of the 1997-2004 Dodge...
Monroe Load Adjusting 58241 Front Suspension Shock Absorber and Coil Spring Assembly Pk of 2 for Chevrolet C10Ideal for light trucks that that tow or carry varying loads, Monroe load adjusting shocks...
Keep your light truck level and controlled under changing loads with the Monroe Load Adjusting Rear Suspension Shock Absorber and Coil Spring Assembly 58608. This ready-to-install assembly pairs a...
Keep your minivan's rear end level and composed under a full load with the Monroe Shocks & Struts Load Adjusting Suspension Shock Absorber and Coil Spring Assembly 58648. This rear assembly ships as...
WARNING:
These products can expose you to chemicals including lead and phthalates, which are known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to
www.P65Warnings.ca.gov.
