Mevotech TTX Suspension Control Arm and Ball Joint Assembly P/N:CTXMS301209
$162.99
(You save)
Help keep your Nissan's front suspension tight and controlled with the Mevotech TTX control arm and ball joint assembly, MPN CTXMS301209. This front left upper unit installs as a direct-fit replacement for the listed applications and fits many vehicles, among them the 2016-2024 Nissan Titan XD, 2012-2021 Nissan NV1500 and 2012-2021 Nissan NV2500 — see the Buyer's Guide tab for the full list and engine-level fitment.
Stronger build: a stamped steel control arm with a reinforced ball joint head and a thicker, stronger flange to help resist deformation during installation.
Maximum toughness: patented sintered bearings paired with an application-specific ball stud system with a larger sphere.
High-performance design: upgraded rubber bushings with knurling that secures the control arm bushing to the sub-frame.
Easy to install and service: includes a part-specific slotted castle nut and snap cotter pin, a 180-degree SAE grease fitting, and pre-applied nylok thread adhesive to keep fasteners secure and vibration resistant.
A Repel-TEK surface treatment helps prevent rust build-up for a longer service life. The arm locates the wheel while its integrated ball joint lets the steering knuckle pivot and travel; if worn bushings or a loose ball joint are behind clunking, uneven tire wear, or loose steering, this assembly replaces those worn parts in one piece.
What vehicles does the Mevotech TTX CTXMS301209 fit?
It's a front left upper control arm with ball joint that fits many vehicles, among them the 2016-2024 Nissan Titan XD, 2012-2021 Nissan NV1500 and 2012-2021 Nissan NV2500. Check the Buyer's Guide tab for the full list.
Is this an upper or lower control arm?
This is a front left upper control arm with ball joint.
Does it come with installation hardware?
Yes. It includes a part-specific slotted castle nut, a snap cotter pin, and a 180-degree SAE grease fitting, with pre-applied nylok thread adhesive on the fasteners.
What is this Mevotech TTX control arm made of?
It uses a stamped steel control arm with a reinforced ball joint head and a thicker flange, plus patented sintered bearings and a Repel-TEK surface treatment to help resist rust.
What should I know when reading a Mevotech TTX control arm review?
TTX assemblies are built for high-usage commercial and passenger vehicles, SUVs, fleets and working trucks, with upgraded rubber bushings and a larger-sphere ball stud for durability.
Write a Review
Mevotech TTX
Mevotech TTX Suspension Control Arm and Ball Joint Assembly P/N:CTXMS301209
Suspension Control Arm and Ball Joint AssemblyMevotech TTX™ parts are engineered with cutting-edge technology to be the strongest, most durable parts on the market. Built for high-usage commercial...
Firm up your front end with the Mevotech TTX Suspension Control Arm and Ball Joint Assembly CTXMS401108 — a direct-fit 2013-2019 Ford Escape control arm. This unit mounts in the front right lower...
Help restore steady steering response and stable handling with the Mevotech TTX Suspension Control Arm and Ball Joint Assembly (CTXMS401173) — a direct-fit front right lower replacement for the...
Steer with confidence using the Mevotech TTX control arm and ball joint assembly (CTXMS301210), a front right upper unit that locates the wheel and pivots the steering knuckle to keep your suspension...
Help bring precise handling back to the front suspension with the Mevotech TTX control arm and ball joint assembly (P/N CTXMS401187). This is the front right lower unit, and it drops in as a...
WARNING:
These products can expose you to chemicals including lead and phthalates, which are known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to
www.P65Warnings.ca.gov.
