Mevotech TTX Suspension Control Arm and Ball Joint Assembly P/N:CTXK8710T
$101.99
(You save)
Replace a worn Ford Ranger control arm with the Mevotech TTX Suspension Control Arm and Ball Joint Assembly (CTXK8710T), a front right upper unit that helps support and locate the suspension while its integrated ball joint allows the wheel to steer and travel. It's a direct-fit replacement for the listed applications, including the 1998-2011 Ford Ranger, 1995-2001 Ford Explorer, 2001-2003 Ford Explorer Sport, 2001-2005 Ford Explorer Sport Trac, 1997-2001 Mercury Mountaineer, 1999-2001 Mazda B2500, 1998-2008 Mazda B3000 and 1998-2010 Mazda B4000 — see the Buyer's Guide tab for engine coverage and the full list.
Stronger build: forged steel control arm with a thicker cross section for added durability.
Maximum toughness: patented sintered bearings for longer-lasting performance.
Locks out contaminants: a patented sealing ring permanently locks the boot onto the ball joint housing for a superior seal.
Simple to service: includes a 180-degree SAE grease fitting, plus Repel-TEK surface treatment to resist rust build-up.
The ball joint uses a thicker, stronger flange to help prevent deformation during installation, and pre-applied nylok thread adhesive keeps fasteners secure and vibration resistant. Fasteners are included: an application-specific pinch bolt and locking nut. Signs this part may need replacing include clunking on acceleration or over the road, loose or wandering steering, and uneven tire wear.
Frequently Asked Questions
What vehicles does the Mevotech TTX control arm CTXK8710T fit?
It's a direct-fit replacement for the 1998-2011 Ford Ranger, 1995-2001 Ford Explorer, 1997-2001 Mercury Mountaineer, and Mazda B2500/B3000/B4000. See the Buyer's Guide tab for the full list and engine coverage.
Does this fit a 2011 Ford Explorer?
No. This assembly is cataloged for the 1995-2001 Ford Explorer. Always confirm your exact year and model against the Buyer's Guide before ordering.
What position is this control arm and ball joint assembly?
It is cataloged as the front right (passenger-side) upper unit. It is sold individually; order the matching part for the opposite side if you're replacing both.
Are mounting fasteners included?
Yes. Mevotech includes an application-specific pinch bolt and locking nut to install the ball joint, and pre-applied nylok thread adhesive helps keep fasteners secure and vibration resistant.
What are signs this part may need replacing?
Common signs include clunking on acceleration or over bumps, loose or wandering steering, and uneven front tire wear. Have the cause diagnosed, since these symptoms can have other sources.
Write a Review
MEVOTECH
Mevotech TTX Suspension Control Arm and Ball Joint Assembly P/N:CTXK8710T
Locate your front wheel and keep steering tight with the Mevotech TTX control arm and ball joint assembly, MPN CTXMS501239. This is the front left lower unit, and it drops in as a direct-fit...
Keep the front suspension tight and precise with the Mevotech TTX Suspension Control Arm and Ball Joint Assembly (CTXK80306) — a direct-fit F-150 control arm that locates the front-left-upper...
Dial in tight, controlled steering with the Mevotech TTX control arm and ball joint assembly (CTXMS20328), a heavy-duty replacement for the front right (passenger-side) lower position. This complete...
Tighten up a worn Jeep Grand Cherokee control arm with the Mevotech TTX Suspension Control Arm and Ball Joint Assembly CTXMS251100, a direct-fit replacement for the front left upper position on the...
Keep your front wheel located and your steering precise with the Mevotech TTX Suspension Control Arm and Ball Joint Assembly (CTXMS401107), a heavy-duty Ford Escape control arm that drops in as a...
WARNING:
These products can expose you to chemicals including lead and phthalates, which are known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to
www.P65Warnings.ca.gov.
