Mevotech TTX Suspension Control Arm and Ball Joint Assembly P/N:CTXMS25168
$164.99
(You save)
Silence loose, wandering steering and restore tight front-end geometry with the Mevotech TTX Suspension Control Arm and Ball Joint Assembly (CTXMS25168) — a front upper control arm and ball joint assembly built for high-usage commercial and passenger trucks, SUVs, fleets and working trucks. As a Ram 1500 upper control arm, it installs as a direct-fit replacement for the 2006-2008 Dodge Ram 1500, the 2006-2010 Dodge Ram 2500 and Dodge Ram 3500, and the 2006-2013 Ram 2500 and Ram 3500. See the Buyer's Guide tab for the full engine-level list.
Maximum toughness: patented sintered bearings for longer-lasting performance.
Locks out contaminants: a patented sealing ring permanently locks the boot onto the ball joint housing.
Simple to service: a 90-degree SAE grease fitting is included, and a part-specific slotted castle nut and snap cotter pin are provided for installation.
Stamped steel construction is engineered to meet or exceed OE specifications, with Repel-TEK surface treatment to resist rust for longer life.
An application-specific ball stud system with a larger sphere and a thicker, stronger flange helps prevent deformation during installation, and pre-applied nylok thread adhesive keeps fasteners secure and vibration-resistant. If a worn upper ball joint or control arm bushing on your Ram 1500 control arm is causing clunking, uneven tire wear or steering play, this assembly replaces it. Sold individually; the left and right sides install as a pair, so order two for a complete front replacement.
Frequently Asked Questions
Does this Dodge Ram 1500 control arm fit my truck?
It is a direct-fit replacement for the 2006-2008 Dodge Ram 1500, 2006-2010 Dodge Ram 2500 and 3500, and 2006-2013 Ram 2500 and 3500. Check the Buyer's Guide tab to confirm your exact application.
Is this an upper or lower control arm?
This is cataloged as a front upper control arm and ball joint assembly for the listed applications.
Does it include the ball joint and mounting hardware?
Yes. The ball joint is integrated into the assembly, and a part-specific slotted castle nut and snap cotter pin are provided for installation.
Can this control arm be greased?
Yes. A 90-degree SAE grease fitting is included so you can service the ball joint after installation.
Should I replace both sides at once?
The left and right arms install as a pair. Replacing both sides together is a good practice for balanced, even front-end wear. This listing is for one assembly, so order two for both sides.
Write a Review
MEVOTECH
Mevotech TTX Suspension Control Arm and Ball Joint Assembly P/N:CTXMS25168
Locate your front wheel and keep steering tight with the Mevotech TTX control arm and ball joint assembly, MPN CTXMS501239. This is the front left lower unit, and it drops in as a direct-fit...
Keep the front suspension tight and precise with the Mevotech TTX Suspension Control Arm and Ball Joint Assembly (CTXK80306) — a direct-fit F-150 control arm that locates the front-left-upper...
Replace a worn Ford Ranger control arm with the Mevotech TTX Suspension Control Arm and Ball Joint Assembly (CTXK8710T), a front right upper unit that helps support and locate the suspension while...
Dial in tight, controlled steering with the Mevotech TTX control arm and ball joint assembly (CTXMS20328), a heavy-duty replacement for the front right (passenger-side) lower position. This complete...
Tighten up a worn Jeep Grand Cherokee control arm with the Mevotech TTX Suspension Control Arm and Ball Joint Assembly CTXMS251100, a direct-fit replacement for the front left upper position on the...
WARNING:
These products can expose you to chemicals including lead and phthalates, which are known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to
www.P65Warnings.ca.gov.
